Blame | Last modification | View Log | RSS feed
/********************************************************************** Standard register and bit definitions for the Texas Instruments* MSP430 microcontroller.** This file supports assembler and C development for* MSP430G2101 devices.** Texas Instruments, Version 1.0** Rev. 1.0, Setup*********************************************************************/#ifndef __MSP430G2101#define __MSP430G2101#ifdef __cplusplusextern "C" {#endif/*----------------------------------------------------------------------------*//* PERIPHERAL FILE MAP *//*----------------------------------------------------------------------------*//* External references resolved by a device-specific linker command file */#define SFR_8BIT(address) extern volatile unsigned char address#define SFR_16BIT(address) extern volatile unsigned int address/************************************************************* STANDARD BITS************************************************************/#define BIT0 (0x0001)#define BIT1 (0x0002)#define BIT2 (0x0004)#define BIT3 (0x0008)#define BIT4 (0x0010)#define BIT5 (0x0020)#define BIT6 (0x0040)#define BIT7 (0x0080)#define BIT8 (0x0100)#define BIT9 (0x0200)#define BITA (0x0400)#define BITB (0x0800)#define BITC (0x1000)#define BITD (0x2000)#define BITE (0x4000)#define BITF (0x8000)/************************************************************* STATUS REGISTER BITS************************************************************/#define C (0x0001)#define Z (0x0002)#define N (0x0004)#define V (0x0100)#define GIE (0x0008)#define CPUOFF (0x0010)#define OSCOFF (0x0020)#define SCG0 (0x0040)#define SCG1 (0x0080)/* Low Power Modes coded with Bits 4-7 in SR */#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define LPM0 (CPUOFF)#define LPM1 (SCG0+CPUOFF)#define LPM2 (SCG1+CPUOFF)#define LPM3 (SCG1+SCG0+CPUOFF)#define LPM4 (SCG1+SCG0+OSCOFF+CPUOFF)/* End #defines for assembler */#else /* Begin #defines for C */#define LPM0_bits (CPUOFF)#define LPM1_bits (SCG0+CPUOFF)#define LPM2_bits (SCG1+CPUOFF)#define LPM3_bits (SCG1+SCG0+CPUOFF)#define LPM4_bits (SCG1+SCG0+OSCOFF+CPUOFF)#include "in430.h"#define LPM0 _bis_SR_register(LPM0_bits) /* Enter Low Power Mode 0 */#define LPM0_EXIT _bic_SR_register_on_exit(LPM0_bits) /* Exit Low Power Mode 0 */#define LPM1 _bis_SR_register(LPM1_bits) /* Enter Low Power Mode 1 */#define LPM1_EXIT _bic_SR_register_on_exit(LPM1_bits) /* Exit Low Power Mode 1 */#define LPM2 _bis_SR_register(LPM2_bits) /* Enter Low Power Mode 2 */#define LPM2_EXIT _bic_SR_register_on_exit(LPM2_bits) /* Exit Low Power Mode 2 */#define LPM3 _bis_SR_register(LPM3_bits) /* Enter Low Power Mode 3 */#define LPM3_EXIT _bic_SR_register_on_exit(LPM3_bits) /* Exit Low Power Mode 3 */#define LPM4 _bis_SR_register(LPM4_bits) /* Enter Low Power Mode 4 */#define LPM4_EXIT _bic_SR_register_on_exit(LPM4_bits) /* Exit Low Power Mode 4 */#endif /* End #defines for C *//************************************************************* PERIPHERAL FILE MAP************************************************************//************************************************************* SPECIAL FUNCTION REGISTER ADDRESSES + CONTROL BITS************************************************************/SFR_8BIT(IE1); /* Interrupt Enable 1 */#define WDTIE (0x01) /* Watchdog Interrupt Enable */#define OFIE (0x02) /* Osc. Fault Interrupt Enable */#define NMIIE (0x10) /* NMI Interrupt Enable */#define ACCVIE (0x20) /* Flash Access Violation Interrupt Enable */SFR_8BIT(IFG1); /* Interrupt Flag 1 */#define WDTIFG (0x01) /* Watchdog Interrupt Flag */#define OFIFG (0x02) /* Osc. Fault Interrupt Flag */#define PORIFG (0x04) /* Power On Interrupt Flag */#define RSTIFG (0x08) /* Reset Interrupt Flag */#define NMIIFG (0x10) /* NMI Interrupt Flag *//************************************************************* Basic Clock Module************************************************************/#define __MSP430_HAS_BC2__ /* Definition to show that Module is available */SFR_8BIT(DCOCTL); /* DCO Clock Frequency Control */SFR_8BIT(BCSCTL1); /* Basic Clock System Control 1 */SFR_8BIT(BCSCTL2); /* Basic Clock System Control 2 */SFR_8BIT(BCSCTL3); /* Basic Clock System Control 3 */#define MOD0 (0x01) /* Modulation Bit 0 */#define MOD1 (0x02) /* Modulation Bit 1 */#define MOD2 (0x04) /* Modulation Bit 2 */#define MOD3 (0x08) /* Modulation Bit 3 */#define MOD4 (0x10) /* Modulation Bit 4 */#define DCO0 (0x20) /* DCO Select Bit 0 */#define DCO1 (0x40) /* DCO Select Bit 1 */#define DCO2 (0x80) /* DCO Select Bit 2 */#define RSEL0 (0x01) /* Range Select Bit 0 */#define RSEL1 (0x02) /* Range Select Bit 1 */#define RSEL2 (0x04) /* Range Select Bit 2 */#define RSEL3 (0x08) /* Range Select Bit 3 */#define DIVA0 (0x10) /* ACLK Divider 0 */#define DIVA1 (0x20) /* ACLK Divider 1 */#define XTS (0x40) /* LFXTCLK 0:Low Freq. / 1: High Freq. */#define XT2OFF (0x80) /* Enable XT2CLK */#define DIVA_0 (0x00) /* ACLK Divider 0: /1 */#define DIVA_1 (0x10) /* ACLK Divider 1: /2 */#define DIVA_2 (0x20) /* ACLK Divider 2: /4 */#define DIVA_3 (0x30) /* ACLK Divider 3: /8 */#define DIVS0 (0x02) /* SMCLK Divider 0 */#define DIVS1 (0x04) /* SMCLK Divider 1 */#define SELS (0x08) /* SMCLK Source Select 0:DCOCLK / 1:XT2CLK/LFXTCLK */#define DIVM0 (0x10) /* MCLK Divider 0 */#define DIVM1 (0x20) /* MCLK Divider 1 */#define SELM0 (0x40) /* MCLK Source Select 0 */#define SELM1 (0x80) /* MCLK Source Select 1 */#define DIVS_0 (0x00) /* SMCLK Divider 0: /1 */#define DIVS_1 (0x02) /* SMCLK Divider 1: /2 */#define DIVS_2 (0x04) /* SMCLK Divider 2: /4 */#define DIVS_3 (0x06) /* SMCLK Divider 3: /8 */#define DIVM_0 (0x00) /* MCLK Divider 0: /1 */#define DIVM_1 (0x10) /* MCLK Divider 1: /2 */#define DIVM_2 (0x20) /* MCLK Divider 2: /4 */#define DIVM_3 (0x30) /* MCLK Divider 3: /8 */#define SELM_0 (0x00) /* MCLK Source Select 0: DCOCLK */#define SELM_1 (0x40) /* MCLK Source Select 1: DCOCLK */#define SELM_2 (0x80) /* MCLK Source Select 2: XT2CLK/LFXTCLK */#define SELM_3 (0xC0) /* MCLK Source Select 3: LFXTCLK */#define LFXT1OF (0x01) /* Low/high Frequency Oscillator Fault Flag */#define XT2OF (0x02) /* High frequency oscillator 2 fault flag */#define XCAP0 (0x04) /* XIN/XOUT Cap 0 */#define XCAP1 (0x08) /* XIN/XOUT Cap 1 */#define LFXT1S0 (0x10) /* Mode 0 for LFXT1 (XTS = 0) */#define LFXT1S1 (0x20) /* Mode 1 for LFXT1 (XTS = 0) */#define XT2S0 (0x40) /* Mode 0 for XT2 */#define XT2S1 (0x80) /* Mode 1 for XT2 */#define XCAP_0 (0x00) /* XIN/XOUT Cap : 0 pF */#define XCAP_1 (0x04) /* XIN/XOUT Cap : 6 pF */#define XCAP_2 (0x08) /* XIN/XOUT Cap : 10 pF */#define XCAP_3 (0x0C) /* XIN/XOUT Cap : 12.5 pF */#define LFXT1S_0 (0x00) /* Mode 0 for LFXT1 : Normal operation */#define LFXT1S_1 (0x10) /* Mode 1 for LFXT1 : Reserved */#define LFXT1S_2 (0x20) /* Mode 2 for LFXT1 : VLO */#define LFXT1S_3 (0x30) /* Mode 3 for LFXT1 : Digital input signal */#define XT2S_0 (0x00) /* Mode 0 for XT2 : 0.4 - 1 MHz */#define XT2S_1 (0x40) /* Mode 1 for XT2 : 1 - 4 MHz */#define XT2S_2 (0x80) /* Mode 2 for XT2 : 2 - 16 MHz */#define XT2S_3 (0xC0) /* Mode 3 for XT2 : Digital input signal *//************************************************************** Flash Memory*************************************************************/#define __MSP430_HAS_FLASH2__ /* Definition to show that Module is available */SFR_16BIT(FCTL1); /* FLASH Control 1 */SFR_16BIT(FCTL2); /* FLASH Control 2 */SFR_16BIT(FCTL3); /* FLASH Control 3 */#define FRKEY (0x9600) /* Flash key returned by read */#define FWKEY (0xA500) /* Flash key for write */#define FXKEY (0x3300) /* for use with XOR instruction */#define ERASE (0x0002) /* Enable bit for Flash segment erase */#define MERAS (0x0004) /* Enable bit for Flash mass erase */#define WRT (0x0040) /* Enable bit for Flash write */#define BLKWRT (0x0080) /* Enable bit for Flash segment write */#define SEGWRT (0x0080) /* old definition */ /* Enable bit for Flash segment write */#define FN0 (0x0001) /* Divide Flash clock by 1 to 64 using FN0 to FN5 according to: */#define FN1 (0x0002) /* 32*FN5 + 16*FN4 + 8*FN3 + 4*FN2 + 2*FN1 + FN0 + 1 */#ifndef FN2#define FN2 (0x0004)#endif#ifndef FN3#define FN3 (0x0008)#endif#ifndef FN4#define FN4 (0x0010)#endif#define FN5 (0x0020)#define FSSEL0 (0x0040) /* Flash clock select 0 */ /* to distinguish from USART SSELx */#define FSSEL1 (0x0080) /* Flash clock select 1 */#define FSSEL_0 (0x0000) /* Flash clock select: 0 - ACLK */#define FSSEL_1 (0x0040) /* Flash clock select: 1 - MCLK */#define FSSEL_2 (0x0080) /* Flash clock select: 2 - SMCLK */#define FSSEL_3 (0x00C0) /* Flash clock select: 3 - SMCLK */#define BUSY (0x0001) /* Flash busy: 1 */#define KEYV (0x0002) /* Flash Key violation flag */#define ACCVIFG (0x0004) /* Flash Access violation flag */#define WAIT (0x0008) /* Wait flag for segment write */#define LOCK (0x0010) /* Lock bit: 1 - Flash is locked (read only) */#define EMEX (0x0020) /* Flash Emergency Exit */#define LOCKA (0x0040) /* Segment A Lock bit: read = 1 - Segment is locked (read only) */#define FAIL (0x0080) /* Last Program or Erase failed *//************************************************************* DIGITAL I/O Port1/2 Pull up / Pull down Resistors************************************************************/#define __MSP430_HAS_PORT1_R__ /* Definition to show that Module is available */#define __MSP430_HAS_PORT2_R__ /* Definition to show that Module is available */SFR_8BIT(P1IN); /* Port 1 Input */SFR_8BIT(P1OUT); /* Port 1 Output */SFR_8BIT(P1DIR); /* Port 1 Direction */SFR_8BIT(P1IFG); /* Port 1 Interrupt Flag */SFR_8BIT(P1IES); /* Port 1 Interrupt Edge Select */SFR_8BIT(P1IE); /* Port 1 Interrupt Enable */SFR_8BIT(P1SEL); /* Port 1 Selection */SFR_8BIT(P1REN); /* Port 1 Resistor Enable */SFR_8BIT(P2IN); /* Port 2 Input */SFR_8BIT(P2OUT); /* Port 2 Output */SFR_8BIT(P2DIR); /* Port 2 Direction */SFR_8BIT(P2IFG); /* Port 2 Interrupt Flag */SFR_8BIT(P2IES); /* Port 2 Interrupt Edge Select */SFR_8BIT(P2IE); /* Port 2 Interrupt Enable */SFR_8BIT(P2SEL); /* Port 2 Selection */SFR_8BIT(P2REN); /* Port 2 Resistor Enable *//************************************************************* Timer A2************************************************************/#define __MSP430_HAS_TA2__ /* Definition to show that Module is available */SFR_16BIT(TAIV); /* Timer A Interrupt Vector Word */SFR_16BIT(TACTL); /* Timer A Control */SFR_16BIT(TACCTL0); /* Timer A Capture/Compare Control 0 */SFR_16BIT(TACCTL1); /* Timer A Capture/Compare Control 1 */SFR_16BIT(TAR); /* Timer A Counter Register */SFR_16BIT(TACCR0); /* Timer A Capture/Compare 0 */SFR_16BIT(TACCR1); /* Timer A Capture/Compare 1 *//* Alternate register names */#define CCTL0 TACCTL0 /* Timer A Capture/Compare Control 0 */#define CCTL1 TACCTL1 /* Timer A Capture/Compare Control 1 */#define CCR0 TACCR0 /* Timer A Capture/Compare 0 */#define CCR1 TACCR1 /* Timer A Capture/Compare 1 */#define CCTL0_ TACCTL0_ /* Timer A Capture/Compare Control 0 */#define CCTL1_ TACCTL1_ /* Timer A Capture/Compare Control 1 */#define CCR0_ TACCR0_ /* Timer A Capture/Compare 0 */#define CCR1_ TACCR1_ /* Timer A Capture/Compare 1 *//* Alternate register names - 5xx style */#define TA0IV TAIV /* Timer A Interrupt Vector Word */#define TA0CTL TACTL /* Timer A Control */#define TA0CCTL0 TACCTL0 /* Timer A Capture/Compare Control 0 */#define TA0CCTL1 TACCTL1 /* Timer A Capture/Compare Control 1 */#define TA0R TAR /* Timer A Counter Register */#define TA0CCR0 TACCR0 /* Timer A Capture/Compare 0 */#define TA0CCR1 TACCR1 /* Timer A Capture/Compare 1 */#define TA0IV_ TAIV_ /* Timer A Interrupt Vector Word */#define TA0CTL_ TACTL_ /* Timer A Control */#define TA0CCTL0_ TACCTL0_ /* Timer A Capture/Compare Control 0 */#define TA0CCTL1_ TACCTL1_ /* Timer A Capture/Compare Control 1 */#define TA0R_ TAR_ /* Timer A Counter Register */#define TA0CCR0_ TACCR0_ /* Timer A Capture/Compare 0 */#define TA0CCR1_ TACCR1_ /* Timer A Capture/Compare 1 */#define TASSEL1 (0x0200) /* Timer A clock source select 0 */#define TASSEL0 (0x0100) /* Timer A clock source select 1 */#define ID1 (0x0080) /* Timer A clock input divider 1 */#define ID0 (0x0040) /* Timer A clock input divider 0 */#define MC1 (0x0020) /* Timer A mode control 1 */#define MC0 (0x0010) /* Timer A mode control 0 */#define TACLR (0x0004) /* Timer A counter clear */#define TAIE (0x0002) /* Timer A counter interrupt enable */#define TAIFG (0x0001) /* Timer A counter interrupt flag */#define MC_0 (0*0x10u) /* Timer A mode control: 0 - Stop */#define MC_1 (1*0x10u) /* Timer A mode control: 1 - Up to CCR0 */#define MC_2 (2*0x10u) /* Timer A mode control: 2 - Continous up */#define MC_3 (3*0x10u) /* Timer A mode control: 3 - Up/Down */#define ID_0 (0*0x40u) /* Timer A input divider: 0 - /1 */#define ID_1 (1*0x40u) /* Timer A input divider: 1 - /2 */#define ID_2 (2*0x40u) /* Timer A input divider: 2 - /4 */#define ID_3 (3*0x40u) /* Timer A input divider: 3 - /8 */#define TASSEL_0 (0*0x100u) /* Timer A clock source select: 0 - TACLK */#define TASSEL_1 (1*0x100u) /* Timer A clock source select: 1 - ACLK */#define TASSEL_2 (2*0x100u) /* Timer A clock source select: 2 - SMCLK */#define TASSEL_3 (3*0x100u) /* Timer A clock source select: 3 - INCLK */#define CM1 (0x8000) /* Capture mode 1 */#define CM0 (0x4000) /* Capture mode 0 */#define CCIS1 (0x2000) /* Capture input select 1 */#define CCIS0 (0x1000) /* Capture input select 0 */#define SCS (0x0800) /* Capture sychronize */#define SCCI (0x0400) /* Latched capture signal (read) */#define CAP (0x0100) /* Capture mode: 1 /Compare mode : 0 */#define OUTMOD2 (0x0080) /* Output mode 2 */#define OUTMOD1 (0x0040) /* Output mode 1 */#define OUTMOD0 (0x0020) /* Output mode 0 */#define CCIE (0x0010) /* Capture/compare interrupt enable */#define CCI (0x0008) /* Capture input signal (read) */#define OUT (0x0004) /* PWM Output signal if output mode 0 */#define COV (0x0002) /* Capture/compare overflow flag */#define CCIFG (0x0001) /* Capture/compare interrupt flag */#define OUTMOD_0 (0*0x20u) /* PWM output mode: 0 - output only */#define OUTMOD_1 (1*0x20u) /* PWM output mode: 1 - set */#define OUTMOD_2 (2*0x20u) /* PWM output mode: 2 - PWM toggle/reset */#define OUTMOD_3 (3*0x20u) /* PWM output mode: 3 - PWM set/reset */#define OUTMOD_4 (4*0x20u) /* PWM output mode: 4 - toggle */#define OUTMOD_5 (5*0x20u) /* PWM output mode: 5 - Reset */#define OUTMOD_6 (6*0x20u) /* PWM output mode: 6 - PWM toggle/set */#define OUTMOD_7 (7*0x20u) /* PWM output mode: 7 - PWM reset/set */#define CCIS_0 (0*0x1000u) /* Capture input select: 0 - CCIxA */#define CCIS_1 (1*0x1000u) /* Capture input select: 1 - CCIxB */#define CCIS_2 (2*0x1000u) /* Capture input select: 2 - GND */#define CCIS_3 (3*0x1000u) /* Capture input select: 3 - Vcc */#define CM_0 (0*0x4000u) /* Capture mode: 0 - disabled */#define CM_1 (1*0x4000u) /* Capture mode: 1 - pos. edge */#define CM_2 (2*0x4000u) /* Capture mode: 1 - neg. edge */#define CM_3 (3*0x4000u) /* Capture mode: 1 - both edges *//* TA2IV Definitions */#define TAIV_NONE (0x0000) /* No Interrupt pending */#define TAIV_TACCR1 (0x0002) /* TACCR1_CCIFG */#define TAIV_2 (0x0004) /* Reserved */#define TAIV_6 (0x0006) /* Reserved */#define TAIV_8 (0x0008) /* Reserved */#define TAIV_TAIFG (0x000A) /* TAIFG *//************************************************************* WATCHDOG TIMER************************************************************/#define __MSP430_HAS_WDT__ /* Definition to show that Module is available */SFR_16BIT(WDTCTL); /* Watchdog Timer Control *//* The bit names have been prefixed with "WDT" */#define WDTIS0 (0x0001)#define WDTIS1 (0x0002)#define WDTSSEL (0x0004)#define WDTCNTCL (0x0008)#define WDTTMSEL (0x0010)#define WDTNMI (0x0020)#define WDTNMIES (0x0040)#define WDTHOLD (0x0080)#define WDTPW (0x5A00)/* WDT-interval times [1ms] coded with Bits 0-2 *//* WDT is clocked by fSMCLK (assumed 1MHz) */#define WDT_MDLY_32 (WDTPW+WDTTMSEL+WDTCNTCL) /* 32ms interval (default) */#define WDT_MDLY_8 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS0) /* 8ms " */#define WDT_MDLY_0_5 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1) /* 0.5ms " */#define WDT_MDLY_0_064 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1+WDTIS0) /* 0.064ms " *//* WDT is clocked by fACLK (assumed 32KHz) */#define WDT_ADLY_1000 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL) /* 1000ms " */#define WDT_ADLY_250 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS0) /* 250ms " */#define WDT_ADLY_16 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1) /* 16ms " */#define WDT_ADLY_1_9 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0) /* 1.9ms " *//* Watchdog mode -> reset after expired time *//* WDT is clocked by fSMCLK (assumed 1MHz) */#define WDT_MRST_32 (WDTPW+WDTCNTCL) /* 32ms interval (default) */#define WDT_MRST_8 (WDTPW+WDTCNTCL+WDTIS0) /* 8ms " */#define WDT_MRST_0_5 (WDTPW+WDTCNTCL+WDTIS1) /* 0.5ms " */#define WDT_MRST_0_064 (WDTPW+WDTCNTCL+WDTIS1+WDTIS0) /* 0.064ms " *//* WDT is clocked by fACLK (assumed 32KHz) */#define WDT_ARST_1000 (WDTPW+WDTCNTCL+WDTSSEL) /* 1000ms " */#define WDT_ARST_250 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS0) /* 250ms " */#define WDT_ARST_16 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1) /* 16ms " */#define WDT_ARST_1_9 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0) /* 1.9ms " *//* INTERRUPT CONTROL *//* These two bits are defined in the Special Function Registers *//* #define WDTIE 0x01 *//* #define WDTIFG 0x01 *//************************************************************* Calibration Data in Info Mem************************************************************/#ifndef __DisableCalDataSFR_8BIT(CALDCO_1MHZ); /* DCOCTL Calibration Data for 1MHz */SFR_8BIT(CALBC1_1MHZ); /* BCSCTL1 Calibration Data for 1MHz */#endif /* #ifndef __DisableCalData *//************************************************************* Interrupt Vectors (offset from 0xFFE0)************************************************************/#define VECTOR_NAME(name) name##_ptr#define EMIT_PRAGMA(x) _Pragma(#x)#define CREATE_VECTOR(name) void (* const VECTOR_NAME(name))(void) = &name#define PLACE_VECTOR(vector,section) EMIT_PRAGMA(DATA_SECTION(vector,section))#define ISR_VECTOR(func,offset) CREATE_VECTOR(func); \PLACE_VECTOR(VECTOR_NAME(func), offset)#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define PORT1_VECTOR ".int02" /* 0xFFE4 Port 1 */#else#define PORT1_VECTOR (2 * 1u) /* 0xFFE4 Port 1 *//*#define PORT1_ISR(func) ISR_VECTOR(func, ".int02") */ /* 0xFFE4 Port 1 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define PORT2_VECTOR ".int03" /* 0xFFE6 Port 2 */#else#define PORT2_VECTOR (3 * 1u) /* 0xFFE6 Port 2 *//*#define PORT2_ISR(func) ISR_VECTOR(func, ".int03") */ /* 0xFFE6 Port 2 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define TIMERA1_VECTOR ".int08" /* 0xFFF0 Timer A CC1-2, TA */#else#define TIMERA1_VECTOR (8 * 1u) /* 0xFFF0 Timer A CC1-2, TA *//*#define TIMERA1_ISR(func) ISR_VECTOR(func, ".int08") */ /* 0xFFF0 Timer A CC1-2, TA */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define TIMERA0_VECTOR ".int09" /* 0xFFF2 Timer A CC0 */#else#define TIMERA0_VECTOR (9 * 1u) /* 0xFFF2 Timer A CC0 *//*#define TIMERA0_ISR(func) ISR_VECTOR(func, ".int09") */ /* 0xFFF2 Timer A CC0 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define WDT_VECTOR ".int10" /* 0xFFF4 Watchdog Timer */#else#define WDT_VECTOR (10 * 1u) /* 0xFFF4 Watchdog Timer *//*#define WDT_ISR(func) ISR_VECTOR(func, ".int10") */ /* 0xFFF4 Watchdog Timer */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define NMI_VECTOR ".int14" /* 0xFFFC Non-maskable */#else#define NMI_VECTOR (14 * 1u) /* 0xFFFC Non-maskable *//*#define NMI_ISR(func) ISR_VECTOR(func, ".int14") */ /* 0xFFFC Non-maskable */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define RESET_VECTOR ".reset" /* 0xFFFE Reset [Highest Priority] */#else#define RESET_VECTOR (15 * 1u) /* 0xFFFE Reset [Highest Priority] *//*#define RESET_ISR(func) ISR_VECTOR(func, ".int15") */ /* 0xFFFE Reset [Highest Priority] */ /* CCE V2 Style */#endif/************************************************************* End of Modules************************************************************/#ifdef __cplusplus}#endif /* extern "C" */#endif /* #ifndef __MSP430G2101 */