Blame | Last modification | View Log | RSS feed
/********************************************************************** Standard register and bit definitions for the Texas Instruments* MSP430 microcontroller.** This file supports assembler and C development for* MSP430x41x2 devices.** Texas Instruments, Version 1.2** Rev. 1.0, First Release* Rev. 1.1, Fixed typo in ADC10: SREF3 -> SREF2* Rev. 1.2, Corrected OSCCAP settings*********************************************************************/#ifndef __msp430x41x2#define __msp430x41x2#ifdef __cplusplusextern "C" {#endif/*----------------------------------------------------------------------------*//* PERIPHERAL FILE MAP *//*----------------------------------------------------------------------------*//* External references resolved by a device-specific linker command file */#define SFR_8BIT(address) extern volatile unsigned char address#define SFR_16BIT(address) extern volatile unsigned int address/************************************************************* STANDARD BITS************************************************************/#define BIT0 (0x0001)#define BIT1 (0x0002)#define BIT2 (0x0004)#define BIT3 (0x0008)#define BIT4 (0x0010)#define BIT5 (0x0020)#define BIT6 (0x0040)#define BIT7 (0x0080)#define BIT8 (0x0100)#define BIT9 (0x0200)#define BITA (0x0400)#define BITB (0x0800)#define BITC (0x1000)#define BITD (0x2000)#define BITE (0x4000)#define BITF (0x8000)/************************************************************* STATUS REGISTER BITS************************************************************/#define C (0x0001)#define Z (0x0002)#define N (0x0004)#define V (0x0100)#define GIE (0x0008)#define CPUOFF (0x0010)#define OSCOFF (0x0020)#define SCG0 (0x0040)#define SCG1 (0x0080)/* Low Power Modes coded with Bits 4-7 in SR */#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define LPM0 (CPUOFF)#define LPM1 (SCG0+CPUOFF)#define LPM2 (SCG1+CPUOFF)#define LPM3 (SCG1+SCG0+CPUOFF)#define LPM4 (SCG1+SCG0+OSCOFF+CPUOFF)/* End #defines for assembler */#else /* Begin #defines for C */#define LPM0_bits (CPUOFF)#define LPM1_bits (SCG0+CPUOFF)#define LPM2_bits (SCG1+CPUOFF)#define LPM3_bits (SCG1+SCG0+CPUOFF)#define LPM4_bits (SCG1+SCG0+OSCOFF+CPUOFF)#include "in430.h"#define LPM0 _bis_SR_register(LPM0_bits) /* Enter Low Power Mode 0 */#define LPM0_EXIT _bic_SR_register_on_exit(LPM0_bits) /* Exit Low Power Mode 0 */#define LPM1 _bis_SR_register(LPM1_bits) /* Enter Low Power Mode 1 */#define LPM1_EXIT _bic_SR_register_on_exit(LPM1_bits) /* Exit Low Power Mode 1 */#define LPM2 _bis_SR_register(LPM2_bits) /* Enter Low Power Mode 2 */#define LPM2_EXIT _bic_SR_register_on_exit(LPM2_bits) /* Exit Low Power Mode 2 */#define LPM3 _bis_SR_register(LPM3_bits) /* Enter Low Power Mode 3 */#define LPM3_EXIT _bic_SR_register_on_exit(LPM3_bits) /* Exit Low Power Mode 3 */#define LPM4 _bis_SR_register(LPM4_bits) /* Enter Low Power Mode 4 */#define LPM4_EXIT _bic_SR_register_on_exit(LPM4_bits) /* Exit Low Power Mode 4 */#endif /* End #defines for C *//************************************************************* PERIPHERAL FILE MAP************************************************************//************************************************************* SPECIAL FUNCTION REGISTER ADDRESSES + CONTROL BITS************************************************************/SFR_8BIT(IE1); /* Interrupt Enable 1 */#define WDTIE (0x01) /* Watchdog Interrupt Enable */#define OFIE (0x02) /* Osc. Fault Interrupt Enable */#define NMIIE (0x10) /* NMI Interrupt Enable */#define ACCVIE (0x20) /* Flash Access Violation Interrupt Enable */SFR_8BIT(IFG1); /* Interrupt Flag 1 */#define WDTIFG (0x01) /* Watchdog Interrupt Flag */#define OFIFG (0x02) /* Osc. Fault Interrupt Flag */#define PORIFG (0x04) /* Power On Interrupt Flag */#define RSTIFG (0x08) /* Reset Interrupt Flag */#define NMIIFG (0x10) /* NMI Interrupt Flag */SFR_8BIT(IE2); /* Interrupt Enable 2 */#define UC0IE IE2#define UCA0RXIE (0x01)#define UCA0TXIE (0x02)#define UCB0RXIE (0x04)#define UCB0TXIE (0x08)#define BTIE (0x80)SFR_8BIT(IFG2); /* Interrupt Flag 2 */#define UC0IFG IFG2#define UCA0RXIFG (0x01)#define UCA0TXIFG (0x02)#define UCB0RXIFG (0x04)#define UCB0TXIFG (0x08)#define BTIFG (0x80)/************************************************************* ADC10************************************************************/#define __MSP430_HAS_ADC10__ /* Definition to show that Module is available */SFR_8BIT(ADC10DTC0); /* ADC10 Data Transfer Control 0 */SFR_8BIT(ADC10DTC1); /* ADC10 Data Transfer Control 1 */SFR_8BIT(ADC10AE0); /* ADC10 Analog Enable 0 */SFR_8BIT(ADC10AE1); /* ADC10 Analog Enable 1 */SFR_16BIT(ADC10CTL0); /* ADC10 Control 0 */SFR_16BIT(ADC10CTL1); /* ADC10 Control 1 */SFR_16BIT(ADC10MEM); /* ADC10 Memory */SFR_16BIT(ADC10SA); /* ADC10 Data Transfer Start Address *//* ADC10CTL0 */#define ADC10SC (0x001) /* ADC10 Start Conversion */#define ENC (0x002) /* ADC10 Enable Conversion */#define ADC10IFG (0x004) /* ADC10 Interrupt Flag */#define ADC10IE (0x008) /* ADC10 Interrupt Enalbe */#define ADC10ON (0x010) /* ADC10 On/Enable */#define REFON (0x020) /* ADC10 Reference on */#define REF2_5V (0x040) /* ADC10 Ref 0:1.5V / 1:2.5V */#define MSC (0x080) /* ADC10 Multiple SampleConversion */#define REFBURST (0x100) /* ADC10 Reference Burst Mode */#define REFOUT (0x200) /* ADC10 Enalbe output of Ref. */#define ADC10SR (0x400) /* ADC10 Sampling Rate 0:200ksps / 1:50ksps */#define ADC10SHT0 (0x800) /* ADC10 Sample Hold Select Bit: 0 */#define ADC10SHT1 (0x1000) /* ADC10 Sample Hold Select Bit: 1 */#define SREF0 (0x2000) /* ADC10 Reference Select Bit: 0 */#define SREF1 (0x4000) /* ADC10 Reference Select Bit: 1 */#define SREF2 (0x8000) /* ADC10 Reference Select Bit: 2 */#define ADC10SHT_0 (0*0x800u) /* 4 x ADC10CLKs */#define ADC10SHT_1 (1*0x800u) /* 8 x ADC10CLKs */#define ADC10SHT_2 (2*0x800u) /* 16 x ADC10CLKs */#define ADC10SHT_3 (3*0x800u) /* 64 x ADC10CLKs */#define SREF_0 (0*0x2000u) /* VR+ = AVCC and VR- = AVSS */#define SREF_1 (1*0x2000u) /* VR+ = VREF+ and VR- = AVSS */#define SREF_2 (2*0x2000u) /* VR+ = VEREF+ and VR- = AVSS */#define SREF_3 (3*0x2000u) /* VR+ = VEREF+ and VR- = AVSS */#define SREF_4 (4*0x2000u) /* VR+ = AVCC and VR- = VREF-/VEREF- */#define SREF_5 (5*0x2000u) /* VR+ = VREF+ and VR- = VREF-/VEREF- */#define SREF_6 (6*0x2000u) /* VR+ = VEREF+ and VR- = VREF-/VEREF- */#define SREF_7 (7*0x2000u) /* VR+ = VEREF+ and VR- = VREF-/VEREF- *//* ADC10CTL1 */#define ADC10BUSY (0x0001) /* ADC10 BUSY */#define CONSEQ0 (0x0002) /* ADC10 Conversion Sequence Select 0 */#define CONSEQ1 (0x0004) /* ADC10 Conversion Sequence Select 1 */#define ADC10SSEL0 (0x0008) /* ADC10 Clock Source Select Bit: 0 */#define ADC10SSEL1 (0x0010) /* ADC10 Clock Source Select Bit: 1 */#define ADC10DIV0 (0x0020) /* ADC10 Clock Divider Select Bit: 0 */#define ADC10DIV1 (0x0040) /* ADC10 Clock Divider Select Bit: 1 */#define ADC10DIV2 (0x0080) /* ADC10 Clock Divider Select Bit: 2 */#define ISSH (0x0100) /* ADC10 Invert Sample Hold Signal */#define ADC10DF (0x0200) /* ADC10 Data Format 0:binary 1:2's complement */#define SHS0 (0x0400) /* ADC10 Sample/Hold Source Bit: 0 */#define SHS1 (0x0800) /* ADC10 Sample/Hold Source Bit: 1 */#define INCH0 (0x1000) /* ADC10 Input Channel Select Bit: 0 */#define INCH1 (0x2000) /* ADC10 Input Channel Select Bit: 1 */#define INCH2 (0x4000) /* ADC10 Input Channel Select Bit: 2 */#define INCH3 (0x8000) /* ADC10 Input Channel Select Bit: 3 */#define CONSEQ_0 (0*2u) /* Single channel single conversion */#define CONSEQ_1 (1*2u) /* Sequence of channels */#define CONSEQ_2 (2*2u) /* Repeat single channel */#define CONSEQ_3 (3*2u) /* Repeat sequence of channels */#define ADC10SSEL_0 (0*8u) /* ADC10OSC */#define ADC10SSEL_1 (1*8u) /* ACLK */#define ADC10SSEL_2 (2*8u) /* MCLK */#define ADC10SSEL_3 (3*8u) /* SMCLK */#define ADC10DIV_0 (0*0x20u) /* ADC10 Clock Divider Select 0 */#define ADC10DIV_1 (1*0x20u) /* ADC10 Clock Divider Select 1 */#define ADC10DIV_2 (2*0x20u) /* ADC10 Clock Divider Select 2 */#define ADC10DIV_3 (3*0x20u) /* ADC10 Clock Divider Select 3 */#define ADC10DIV_4 (4*0x20u) /* ADC10 Clock Divider Select 4 */#define ADC10DIV_5 (5*0x20u) /* ADC10 Clock Divider Select 5 */#define ADC10DIV_6 (6*0x20u) /* ADC10 Clock Divider Select 6 */#define ADC10DIV_7 (7*0x20u) /* ADC10 Clock Divider Select 7 */#define SHS_0 (0*0x400u) /* ADC10SC */#define SHS_1 (1*0x400u) /* Ext. SC Trigger 1 */#define SHS_2 (2*0x400u) /* Ext. SC Trigger 2 */#define SHS_3 (3*0x400u) /* Ext. SC Trigger 3 */#define INCH_0 (0*0x1000u) /* Selects Channel 0 */#define INCH_1 (1*0x1000u) /* Selects Channel 1 */#define INCH_2 (2*0x1000u) /* Selects Channel 2 */#define INCH_3 (3*0x1000u) /* Selects Channel 3 */#define INCH_4 (4*0x1000u) /* Selects Channel 4 */#define INCH_5 (5*0x1000u) /* Selects Channel 5 */#define INCH_6 (6*0x1000u) /* Selects Channel 6 */#define INCH_7 (7*0x1000u) /* Selects Channel 7 */#define INCH_8 (8*0x1000u) /* Selects Channel 8 */#define INCH_9 (9*0x1000u) /* Selects Channel 9 */#define INCH_10 (10*0x1000u) /* Selects Channel 10 */#define INCH_11 (11*0x1000u) /* Selects Channel 11 */#define INCH_12 (12*0x1000u) /* Selects Channel 12 */#define INCH_13 (13*0x1000u) /* Selects Channel 13 */#define INCH_14 (14*0x1000u) /* Selects Channel 14 */#define INCH_15 (15*0x1000u) /* Selects Channel 15 *//* ADC10DTC0 */#define ADC10FETCH (0x001) /* This bit should normally be reset */#define ADC10B1 (0x002) /* ADC10 block one */#define ADC10CT (0x004) /* ADC10 continuous transfer */#define ADC10TB (0x008) /* ADC10 two-block mode */#define ADC10DISABLE (0x000) /* ADC10DTC1 *//************************************************************* BASIC TIMER with Real Time Clock************************************************************/#define __MSP430_HAS_BT_RTC__ /* Definition to show that Module is available */SFR_8BIT(BTCTL); /* Basic Timer Control */SFR_8BIT(RTCCTL); /* Real Time Clock Control */SFR_8BIT(RTCNT1); /* Real Time Counter 1 */SFR_8BIT(RTCNT2); /* Real Time Counter 2 */SFR_8BIT(RTCNT3); /* Real Time Counter 3 */SFR_8BIT(RTCNT4); /* Real Time Counter 4 */SFR_8BIT(BTCNT1); /* Basic Timer Count 1 */SFR_8BIT(BTCNT2); /* Basic Timer Count 2 */SFR_8BIT(RTCDAY); /* Real Time Clock Day */SFR_8BIT(RTCMON); /* Real Time Clock Month */SFR_8BIT(RTCYEARL); /* Real Time Clock Year (Low Byte) */SFR_8BIT(RTCYEARH); /* Real Time Clock Year (High Byte) */#define RTCSEC RTCNT1#define RTCMIN RTCNT2#define RTCHOUR RTCNT3#define RTCDOW RTCNT4SFR_16BIT(RTCTL); /* Basic/Real Timer Control */SFR_16BIT(RTCTIM0); /* Real Time Clock Time 0 */SFR_16BIT(RTCTIM1); /* Real Time Clock Time 1 */SFR_16BIT(BTCNT12); /* Basic Timer Count 1/2 */SFR_16BIT(RTCDATE); /* Real Time Clock Date */SFR_16BIT(RTCYEAR); /* Real Time Clock Year */#define RTCNT12 RTCTIM0#define RTCNT34 RTCTIM1#define BTSSEL (0x80) /* fBT = fMCLK (main clock) */#define BTHOLD (0x40) /* BT1 is held if this bit is set */#define BTDIV (0x20) /* fCLK2 = ACLK:256 *///#define res (0x10)//#define res (0x08)#define BTIP2 (0x04)#define BTIP1 (0x02)#define BTIP0 (0x01)#define RTCBCD (0x80) /* RTC BCD Select */#define RTCHOLD (0x40) /* RTC Hold */#define RTCMODE1 (0x20) /* RTC Mode 1 */#define RTCMODE0 (0x10) /* RTC Mode 0 */#define RTCTEV1 (0x08) /* RTC Time Event 1 */#define RTCTEV0 (0x04) /* RTC Time Event 0 */#define RTCIE (0x02) /* RTC Interrupt Enable */#define RTCFG (0x01) /* RTC Event Flag */#define RTCTEV_0 (0x00) /* RTC Time Event: 0 */#define RTCTEV_1 (0x04) /* RTC Time Event: 1 */#define RTCTEV_2 (0x08) /* RTC Time Event: 2 */#define RTCTEV_3 (0x0C) /* RTC Time Event: 3 */#define RTCMODE_0 (0x00) /* RTC Mode: 0 */#define RTCMODE_1 (0x10) /* RTC Mode: 1 */#define RTCMODE_2 (0x20) /* RTC Mode: 2 */#define RTCMODE_3 (0x30) /* RTC Mode: 3 *//* Frequency of the BTCNT2 coded with Bit 5 and 7 in BTCTL */#define BT_fCLK2_ACLK (0x00)#define BT_fCLK2_ACLK_DIV256 (BTDIV)#define BT_fCLK2_MCLK (BTSSEL)/* Interrupt interval time fINT coded with Bits 0-2 in BTCTL */#define BT_fCLK2_DIV2 (0x00) /* fINT = fCLK2:2 (default) */#define BT_fCLK2_DIV4 (BTIP0) /* fINT = fCLK2:4 */#define BT_fCLK2_DIV8 (BTIP1) /* fINT = fCLK2:8 */#define BT_fCLK2_DIV16 (BTIP1+BTIP0) /* fINT = fCLK2:16 */#define BT_fCLK2_DIV32 (BTIP2) /* fINT = fCLK2:32 */#define BT_fCLK2_DIV64 (BTIP2+BTIP0) /* fINT = fCLK2:64 */#define BT_fCLK2_DIV128 (BTIP2+BTIP1) /* fINT = fCLK2:128 */#define BT_fCLK2_DIV256 (BTIP2+BTIP1+BTIP0) /* fINT = fCLK2:256 *//* with assumed vlues of fACLK=32KHz, fMCLK=1MHz *//* fBT=fACLK is thought for longer interval times */#define BT_ADLY_0_064 (0x00) /* 0.064ms interval (default) */#define BT_ADLY_0_125 (BTIP0) /* 0.125ms " */#define BT_ADLY_0_25 (BTIP1) /* 0.25ms " */#define BT_ADLY_0_5 (BTIP1+BTIP0) /* 0.5ms " */#define BT_ADLY_1 (BTIP2) /* 1ms " */#define BT_ADLY_2 (BTIP2+BTIP0) /* 2ms " */#define BT_ADLY_4 (BTIP2+BTIP1) /* 4ms " */#define BT_ADLY_8 (BTIP2+BTIP1+BTIP0) /* 8ms " */#define BT_ADLY_16 (BTDIV) /* 16ms " */#define BT_ADLY_32 (BTDIV+BTIP0) /* 32ms " */#define BT_ADLY_64 (BTDIV+BTIP1) /* 64ms " */#define BT_ADLY_125 (BTDIV+BTIP1+BTIP0) /* 125ms " */#define BT_ADLY_250 (BTDIV+BTIP2) /* 250ms " */#define BT_ADLY_500 (BTDIV+BTIP2+BTIP0) /* 500ms " */#define BT_ADLY_1000 (BTDIV+BTIP2+BTIP1) /* 1000ms " */#define BT_ADLY_2000 (BTDIV+BTIP2+BTIP1+BTIP0) /* 2000ms " *//* fCLK2=fMCLK (1MHz) is thought for short interval times *//* the timing for short intervals is more precise than ACLK *//* NOTE *//* Be sure that the SCFQCTL-Register is set to 01Fh so that fMCLK=1MHz *//* Too low interval time results in interrupts too frequent for the processor to handle! */#define BT_MDLY_0_002 (BTSSEL) /* 0.002ms interval *** interval times */#define BT_MDLY_0_004 (BTSSEL+BTIP0) /* 0.004ms " *** too short for */#define BT_MDLY_0_008 (BTSSEL+BTIP1) /* 0.008ms " *** interrupt */#define BT_MDLY_0_016 (BTSSEL+BTIP1+BTIP0) /* 0.016ms " *** handling */#define BT_MDLY_0_032 (BTSSEL+BTIP2) /* 0.032ms " */#define BT_MDLY_0_064 (BTSSEL+BTIP2+BTIP0) /* 0.064ms " */#define BT_MDLY_0_125 (BTSSEL+BTIP2+BTIP1) /* 0.125ms " */#define BT_MDLY_0_25 (BTSSEL+BTIP2+BTIP1+BTIP0)/* 0.25ms " *//* Hold coded with Bits 6-7 in BT(1)CTL *//* this is for BT */#define BTHOLD_CNT1 (BTHOLD) /* BTCNT1 is held while BTHOLD is set */#define BTHOLD_CNT1_2 (BTHOLD+BTDIV) /* BT1CNT1 .AND. BT1CNT2 are held while ~ is set *//* INTERRUPT CONTROL BITS *//* #define BTIE 0x80 *//* #define BTIFG 0x80 *//************************************************************* Comparator A************************************************************/#define __MSP430_HAS_CAPLUS__ /* Definition to show that Module is available */SFR_8BIT(CACTL1); /* Comparator A Control 1 */SFR_8BIT(CACTL2); /* Comparator A Control 2 */SFR_8BIT(CAPD); /* Comparator A Port Disable */#define CAIFG (0x01) /* Comp. A Interrupt Flag */#define CAIE (0x02) /* Comp. A Interrupt Enable */#define CAIES (0x04) /* Comp. A Int. Edge Select: 0:rising / 1:falling */#define CAON (0x08) /* Comp. A enable */#define CAREF0 (0x10) /* Comp. A Internal Reference Select 0 */#define CAREF1 (0x20) /* Comp. A Internal Reference Select 1 */#define CARSEL (0x40) /* Comp. A Internal Reference Enable */#define CAEX (0x80) /* Comp. A Exchange Inputs */#define CAREF_0 (0x00) /* Comp. A Int. Ref. Select 0 : Off */#define CAREF_1 (0x10) /* Comp. A Int. Ref. Select 1 : 0.25*Vcc */#define CAREF_2 (0x20) /* Comp. A Int. Ref. Select 2 : 0.5*Vcc */#define CAREF_3 (0x30) /* Comp. A Int. Ref. Select 3 : Vt*/#define CAOUT (0x01) /* Comp. A Output */#define CAF (0x02) /* Comp. A Enable Output Filter */#define P2CA0 (0x04) /* Comp. A +Terminal Multiplexer */#define P2CA1 (0x08) /* Comp. A -Terminal Multiplexer */#define P2CA2 (0x10) /* Comp. A -Terminal Multiplexer */#define P2CA3 (0x20) /* Comp. A -Terminal Multiplexer */#define P2CA4 (0x40) /* Comp. A +Terminal Multiplexer */#define CASHORT (0x80) /* Comp. A Short + and - Terminals */#define CAPD0 (0x01) /* Comp. A Disable Input Buffer of Port Register .0 */#define CAPD1 (0x02) /* Comp. A Disable Input Buffer of Port Register .1 */#define CAPD2 (0x04) /* Comp. A Disable Input Buffer of Port Register .2 */#define CAPD3 (0x08) /* Comp. A Disable Input Buffer of Port Register .3 */#define CAPD4 (0x10) /* Comp. A Disable Input Buffer of Port Register .4 */#define CAPD5 (0x20) /* Comp. A Disable Input Buffer of Port Register .5 */#define CAPD6 (0x40) /* Comp. A Disable Input Buffer of Port Register .6 */#define CAPD7 (0x80) /* Comp. A Disable Input Buffer of Port Register .7 *//************************************************************** Flash Memory*************************************************************/#define __MSP430_HAS_FLASH2__ /* Definition to show that Module is available */SFR_16BIT(FCTL1); /* FLASH Control 1 */SFR_16BIT(FCTL2); /* FLASH Control 2 */SFR_16BIT(FCTL3); /* FLASH Control 3 */#define FRKEY (0x9600) /* Flash key returned by read */#define FWKEY (0xA500) /* Flash key for write */#define FXKEY (0x3300) /* for use with XOR instruction */#define ERASE (0x0002) /* Enable bit for Flash segment erase */#define MERAS (0x0004) /* Enable bit for Flash mass erase */#define EEI (0x0008) /* Enable Erase Interrupts */#define EEIEX (0x0010) /* Enable Emergency Interrupt Exit */#define WRT (0x0040) /* Enable bit for Flash write */#define BLKWRT (0x0080) /* Enable bit for Flash segment write */#define SEGWRT (0x0080) /* old definition */ /* Enable bit for Flash segment write */#define FN0 (0x0001) /* Divide Flash clock by 1 to 64 using FN0 to FN5 according to: */#define FN1 (0x0002) /* 32*FN5 + 16*FN4 + 8*FN3 + 4*FN2 + 2*FN1 + FN0 + 1 */#ifndef FN2#define FN2 (0x0004)#endif#ifndef FN3#define FN3 (0x0008)#endif#ifndef FN4#define FN4 (0x0010)#endif#define FN5 (0x0020)#define FSSEL0 (0x0040) /* Flash clock select 0 */ /* to distinguish from USART SSELx */#define FSSEL1 (0x0080) /* Flash clock select 1 */#define FSSEL_0 (0x0000) /* Flash clock select: 0 - ACLK */#define FSSEL_1 (0x0040) /* Flash clock select: 1 - MCLK */#define FSSEL_2 (0x0080) /* Flash clock select: 2 - SMCLK */#define FSSEL_3 (0x00C0) /* Flash clock select: 3 - SMCLK */#define BUSY (0x0001) /* Flash busy: 1 */#define KEYV (0x0002) /* Flash Key violation flag */#define ACCVIFG (0x0004) /* Flash Access violation flag */#define WAIT (0x0008) /* Wait flag for segment write */#define LOCK (0x0010) /* Lock bit: 1 - Flash is locked (read only) */#define EMEX (0x0020) /* Flash Emergency Exit */#define LOCKA (0x0040) /* Segment A Lock bit: read = 1 - Segment is locked (read only) */#define FAIL (0x0080) /* Last Program or Erase failed *//************************************************************* SYSTEM CLOCK, FLL+************************************************************/#define __MSP430_HAS_FLLPLUS__ /* Definition to show that Module is available */SFR_8BIT(SCFI0); /* System Clock Frequency Integrator 0 */#define FN_2 (0x04) /* fDCOCLK = 1.4-12MHz*/#define FN_3 (0x08) /* fDCOCLK = 2.2-17Mhz*/#define FN_4 (0x10) /* fDCOCLK = 3.2-25Mhz*/#define FN_8 (0x20) /* fDCOCLK = 5-40Mhz*/#define FLLD0 (0x40) /* Loop Divider Bit : 0 */#define FLLD1 (0x80) /* Loop Divider Bit : 1 */#define FLLD_1 (0x00) /* Multiply Selected Loop Freq. By 1 */#define FLLD_2 (0x40) /* Multiply Selected Loop Freq. By 2 */#define FLLD_4 (0x80) /* Multiply Selected Loop Freq. By 4 */#define FLLD_8 (0xC0) /* Multiply Selected Loop Freq. By 8 */SFR_8BIT(SCFI1); /* System Clock Frequency Integrator 1 */SFR_8BIT(SCFQCTL); /* System Clock Frequency Control *//* System clock frequency values fMCLK coded with Bits 0-6 in SCFQCTL *//* #define SCFQ_32K 0x00 fMCLK=1*fACLK only a range from */#define SCFQ_64K (0x01) /* fMCLK=2*fACLK 1+1 to 127+1 is possible */#define SCFQ_128K (0x03) /* fMCLK=4*fACLK */#define SCFQ_256K (0x07) /* fMCLK=8*fACLK */#define SCFQ_512K (0x0F) /* fMCLK=16*fACLK */#define SCFQ_1M (0x1F) /* fMCLK=32*fACLK */#define SCFQ_2M (0x3F) /* fMCLK=64*fACLK */#define SCFQ_4M (0x7F) /* fMCLK=128*fACLK */#define SCFQ_M (0x80) /* Modulation Disable */SFR_8BIT(FLL_CTL0); /* FLL+ Control 0 */#define DCOF (0x01) /* DCO Fault Flag */#define LFOF (0x02) /* Low Frequency Oscillator Fault Flag */#define XT1OF (0x04) /* High Frequency Oscillator 1 Fault Flag */#define OSCCAP0 (0x10) /* XIN/XOUT Cap 0 */#define OSCCAP1 (0x20) /* XIN/XOUT Cap 1 */#define XTS_FLL (0x40) /* 1: Selects high-freq. oscillator */#define DCOPLUS (0x80) /* DCO+ Enable */#define XCAP0PF (0x00) /* XIN Cap = XOUT Cap = 0pf */#define XCAP5_5F (0x10) /* XIN Cap = XOUT Cap = 5.5pf */#define XCAP8_5PF (0x20) /* XIN Cap = XOUT Cap = 8.5pf */#define XCAP11PF (0x30) /* XIN Cap = XOUT Cap = 11pf */#define OSCCAP_0 (0x00) /* XIN Cap = XOUT Cap: 0 */#define OSCCAP_1 (0x10) /* XIN Cap = XOUT Cap: 1 */#define OSCCAP_2 (0x20) /* XIN Cap = XOUT Cap: 2 */#define OSCCAP_3 (0x30) /* XIN Cap = XOUT Cap: 3 */SFR_8BIT(FLL_CTL1); /* FLL+ Control 1 */#define FLL_DIV0 (0x01) /* FLL+ Divide Px.x/ACLK 0 */#define FLL_DIV1 (0x02) /* FLL+ Divide Px.x/ACLK 1 */#define SELM0 (0x08) /* MCLK Source Select 0 */#define SELM1 (0x10) /* MCLK Source Select 1 */#define SMCLKOFF (0x40) /* Peripheral Module Clock (SMCLK) disable */#define FLL_DIV_1 (0x00) /* FLL+ Divide Px.x/ACLK By 1 */#define FLL_DIV_2 (0x01) /* FLL+ Divide Px.x/ACLK By 2 */#define FLL_DIV_4 (0x02) /* FLL+ Divide Px.x/ACLK By 4 */#define FLL_DIV_8 (0x03) /* FLL+ Divide Px.x/ACLK By 8 */#define SELM_DCO (0x00) /* Select DCO for CPU MCLK */#define SELM_A (0x18) /* Select A (from LFXT1) for CPU MCLK */SFR_8BIT(FLL_CTL2); /* FLL+ Control 2 */#define LF1XT1S0 (0x10) /* Mode 0 for LFXT1 */#define LF1XT1S1 (0x20) /* Mode 0 for LFXT1 */#define LF1XT1S_0 (0x00) /* Mode 0 for LF : 32kHz */#define LF1XT1S_1 (0x10) /* Mode 1 for LF : reserved */#define LF1XT1S_2 (0x20) /* Mode 2 for LF : VLO */#define LF1XT1S_3 (0x30) /* Mode 3 for LF : Digital input signal *//* INTERRUPT CONTROL BITS *//* These two bits are defined in the Special Function Registers *//* #define OFIFG 0x02 *//* #define OFIE 0x02 *//************************************************************* LCD_A************************************************************/#define __MSP430_HAS_LCD_A__ /* Definition to show that Module is available */SFR_8BIT(LCDACTL); /* LCD_A Control Register */#define LCDON (0x01)#define LCDSON (0x04)#define LCDMX0 (0x08)#define LCDMX1 (0x10)#define LCDFREQ0 (0x20)#define LCDFREQ1 (0x40)#define LCDFREQ2 (0x80)/* Display modes coded with Bits 2-4 */#define LCDSTATIC (LCDSON)#define LCD2MUX (LCDMX0+LCDSON)#define LCD3MUX (LCDMX1+LCDSON)#define LCD4MUX (LCDMX1+LCDMX0+LCDSON)/* Frequency select code with Bits 5-7 */#define LCDFREQ_32 (0x00) /* LCD Freq: ACLK divided by 32 */#define LCDFREQ_64 (0x20) /* LCD Freq: ACLK divided by 64 */#define LCDFREQ_96 (0x40) /* LCD Freq: ACLK divided by 96 */#define LCDFREQ_128 (0x60) /* LCD Freq: ACLK divided by 128 */#define LCDFREQ_192 (0x80) /* LCD Freq: ACLK divided by 192 */#define LCDFREQ_256 (0xA0) /* LCD Freq: ACLK divided by 256 */#define LCDFREQ_384 (0xC0) /* LCD Freq: ACLK divided by 384 */#define LCDFREQ_512 (0xE0) /* LCD Freq: ACLK divided by 512 */SFR_8BIT(LCDAPCTL0); /* LCD_A Port Control Register 0 */#define LCDS0 (0x01) /* LCD Segment 0 to 3 Enable. */#define LCDS4 (0x02) /* LCD Segment 4 to 7 Enable. */#define LCDS8 (0x04) /* LCD Segment 8 to 11 Enable. */#define LCDS12 (0x08) /* LCD Segment 12 to 15 Enable. */#define LCDS16 (0x10) /* LCD Segment 16 to 19 Enable. */#define LCDS20 (0x20) /* LCD Segment 20 to 23 Enable. */#define LCDS24 (0x40) /* LCD Segment 24 to 27 Enable. */#define LCDS28 (0x80) /* LCD Segment 28 to 31 Enable. */SFR_8BIT(LCDAPCTL1); /* LCD_A Port Control Register 1 */#define LCDS32 (0x01) /* LCD Segment 32 to 35 Enable. */#define LCDS36 (0x02) /* LCD Segment 36 to 39 Enable. */SFR_8BIT(LCDAVCTL0); /* LCD_A Voltage Control Register 0 */#define LCD2B (0x01) /* Selects 1/2 bias. */#define VLCDREF0 (0x02) /* Selects reference voltage for regulated charge pump: 0 */#define VLCDREF1 (0x04) /* Selects reference voltage for regulated charge pump: 1 */#define LCDCPEN (0x08) /* LCD Voltage Charge Pump Enable. */#define VLCDEXT (0x10) /* Select external source for VLCD. */#define LCDREXT (0x20) /* Selects external connections for LCD mid voltages. */#define LCDR03EXT (0x40) /* Selects external connection for lowest LCD voltage. *//* Reference voltage source select for the regulated charge pump */#define VLCDREF_0 (0<<1) /* Internal */#define VLCDREF_1 (1<<1) /* External */#define VLCDREF_2 (2<<1) /* Reserved */#define VLCDREF_3 (3<<1) /* Reserved */SFR_8BIT(LCDAVCTL1); /* LCD_A Voltage Control Register 1 */#define VLCD0 (0x02) /* VLCD select: 0 */#define VLCD1 (0x04) /* VLCD select: 1 */#define VLCD2 (0x08) /* VLCD select: 2 */#define VLCD3 (0x10) /* VLCD select: 3 *//* Charge pump voltage selections */#define VLCD_0 (0<<1) /* Charge pump disabled */#define VLCD_1 (1<<1) /* VLCD = 2.60V */#define VLCD_2 (2<<1) /* VLCD = 2.66V */#define VLCD_3 (3<<1) /* VLCD = 2.72V */#define VLCD_4 (4<<1) /* VLCD = 2.78V */#define VLCD_5 (5<<1) /* VLCD = 2.84V */#define VLCD_6 (6<<1) /* VLCD = 2.90V */#define VLCD_7 (7<<1) /* VLCD = 2.96V */#define VLCD_8 (8<<1) /* VLCD = 3.02V */#define VLCD_9 (9<<1) /* VLCD = 3.08V */#define VLCD_10 (10<<1) /* VLCD = 3.14V */#define VLCD_11 (11<<1) /* VLCD = 3.20V */#define VLCD_12 (12<<1) /* VLCD = 3.26V */#define VLCD_13 (12<<1) /* VLCD = 3.32V */#define VLCD_14 (13<<1) /* VLCD = 3.38V */#define VLCD_15 (15<<1) /* VLCD = 3.44V */#define VLCD_DISABLED (0<<1) /* Charge pump disabled */#define VLCD_2_60 (1<<1) /* VLCD = 2.60V */#define VLCD_2_66 (2<<1) /* VLCD = 2.66V */#define VLCD_2_72 (3<<1) /* VLCD = 2.72V */#define VLCD_2_78 (4<<1) /* VLCD = 2.78V */#define VLCD_2_84 (5<<1) /* VLCD = 2.84V */#define VLCD_2_90 (6<<1) /* VLCD = 2.90V */#define VLCD_2_96 (7<<1) /* VLCD = 2.96V */#define VLCD_3_02 (8<<1) /* VLCD = 3.02V */#define VLCD_3_08 (9<<1) /* VLCD = 3.08V */#define VLCD_3_14 (10<<1) /* VLCD = 3.14V */#define VLCD_3_20 (11<<1) /* VLCD = 3.20V */#define VLCD_3_26 (12<<1) /* VLCD = 3.26V */#define VLCD_3_32 (12<<1) /* VLCD = 3.32V */#define VLCD_3_38 (13<<1) /* VLCD = 3.38V */#define VLCD_3_44 (15<<1) /* VLCD = 3.44V */#define LCDMEM_ (0x0091) /* LCD Memory */#ifdef __ASM_HEADER__#define LCDMEM (LCDMEM_) /* LCD Memory (for assembler) */#else#define LCDMEM ((char*) LCDMEM_) /* LCD Memory (for C) */#endifSFR_8BIT(LCDM1); /* LCD Memory 1 */SFR_8BIT(LCDM2); /* LCD Memory 2 */SFR_8BIT(LCDM3); /* LCD Memory 3 */SFR_8BIT(LCDM4); /* LCD Memory 4 */SFR_8BIT(LCDM5); /* LCD Memory 5 */SFR_8BIT(LCDM6); /* LCD Memory 6 */SFR_8BIT(LCDM7); /* LCD Memory 7 */SFR_8BIT(LCDM8); /* LCD Memory 8 */SFR_8BIT(LCDM9); /* LCD Memory 9 */SFR_8BIT(LCDM10); /* LCD Memory 10 */SFR_8BIT(LCDM11); /* LCD Memory 11 */SFR_8BIT(LCDM12); /* LCD Memory 12 */SFR_8BIT(LCDM13); /* LCD Memory 13 */SFR_8BIT(LCDM14); /* LCD Memory 14 */SFR_8BIT(LCDM15); /* LCD Memory 15 */SFR_8BIT(LCDM16); /* LCD Memory 16 */SFR_8BIT(LCDM17); /* LCD Memory 17 */SFR_8BIT(LCDM18); /* LCD Memory 18 */SFR_8BIT(LCDM19); /* LCD Memory 19 */SFR_8BIT(LCDM20); /* LCD Memory 20 */#define LCDMA (LCDM10) /* LCD Memory A */#define LCDMB (LCDM11) /* LCD Memory B */#define LCDMC (LCDM12) /* LCD Memory C */#define LCDMD (LCDM13) /* LCD Memory D */#define LCDME (LCDM14) /* LCD Memory E */#define LCDMF (LCDM15) /* LCD Memory F *//************************************************************* DIGITAL I/O Port1/2************************************************************/#define __MSP430_HAS_PORT1__ /* Definition to show that Module is available */#define __MSP430_HAS_PORT2__ /* Definition to show that Module is available */SFR_8BIT(P1IN); /* Port 1 Input */SFR_8BIT(P1OUT); /* Port 1 Output */SFR_8BIT(P1DIR); /* Port 1 Direction */SFR_8BIT(P1IFG); /* Port 1 Interrupt Flag */SFR_8BIT(P1IES); /* Port 1 Interrupt Edge Select */SFR_8BIT(P1IE); /* Port 1 Interrupt Enable */SFR_8BIT(P1SEL); /* Port 1 Selection */SFR_8BIT(P2IN); /* Port 2 Input */SFR_8BIT(P2OUT); /* Port 2 Output */SFR_8BIT(P2DIR); /* Port 2 Direction */SFR_8BIT(P2IFG); /* Port 2 Interrupt Flag */SFR_8BIT(P2IES); /* Port 2 Interrupt Edge Select */SFR_8BIT(P2IE); /* Port 2 Interrupt Enable */SFR_8BIT(P2SEL); /* Port 2 Selection *//************************************************************* DIGITAL I/O Port3/4************************************************************/#define __MSP430_HAS_PORT3__ /* Definition to show that Module is available */#define __MSP430_HAS_PORT4__ /* Definition to show that Module is available */SFR_8BIT(P3IN); /* Port 3 Input */SFR_8BIT(P3OUT); /* Port 3 Output */SFR_8BIT(P3DIR); /* Port 3 Direction */SFR_8BIT(P3SEL); /* Port 3 Selection */SFR_8BIT(P4IN); /* Port 4 Input */SFR_8BIT(P4OUT); /* Port 4 Output */SFR_8BIT(P4DIR); /* Port 4 Direction */SFR_8BIT(P4SEL); /* Port 4 Selection *//************************************************************* DIGITAL I/O Port5/6************************************************************/#define __MSP430_HAS_PORT5__ /* Definition to show that Module is available */#define __MSP430_HAS_PORT6__ /* Definition to show that Module is available */SFR_8BIT(P5IN); /* Port 5 Input */SFR_8BIT(P5OUT); /* Port 5 Output */SFR_8BIT(P5DIR); /* Port 5 Direction */SFR_8BIT(P5SEL); /* Port 5 Selection */SFR_8BIT(P6IN); /* Port 6 Input */SFR_8BIT(P6OUT); /* Port 6 Output */SFR_8BIT(P6DIR); /* Port 6 Direction */SFR_8BIT(P6SEL); /* Port 6 Selection *//************************************************************* DIGITAL I/O Port7************************************************************/#define __MSP430_HAS_PORT7__ /* Definition to show that Module is available */SFR_8BIT(P7IN); /* Port 7 Input */SFR_8BIT(P7OUT); /* Port 7 Output */SFR_8BIT(P7DIR); /* Port 7 Direction */SFR_8BIT(P7SEL); /* Port 7 Selection *//************************************************************* Brown-Out, Supply Voltage Supervision (SVS)************************************************************/#define __MSP430_HAS_SVS__ /* Definition to show that Module is available */SFR_8BIT(SVSCTL); /* SVS Control */#define SVSFG (0x01) /* SVS Flag */#define SVSOP (0x02) /* SVS output (read only) */#define SVSON (0x04) /* Switches the SVS on/off */#define PORON (0x08) /* Enable POR Generation if Low Voltage */#define VLD0 (0x10)#define VLD1 (0x20)#define VLD2 (0x40)#define VLD3 (0x80)#define VLDON (0x10)#define VLDOFF (0x00)#define VLD_1_8V (0x10)/************************************************************* Timer0_A3************************************************************/#define __MSP430_HAS_TA3__ /* Definition to show that Module is available */SFR_16BIT(TA0IV); /* Timer0_A3 Interrupt Vector Word */SFR_16BIT(TA0CTL); /* Timer0_A3 Control */SFR_16BIT(TA0CCTL0); /* Timer0_A3 Capture/Compare Control 0 */SFR_16BIT(TA0CCTL1); /* Timer0_A3 Capture/Compare Control 1 */SFR_16BIT(TA0CCTL2); /* Timer0_A3 Capture/Compare Control 2 */SFR_16BIT(TA0R); /* Timer0_A3 */SFR_16BIT(TA0CCR0); /* Timer0_A3 Capture/Compare 0 */SFR_16BIT(TA0CCR1); /* Timer0_A3 Capture/Compare 1 */SFR_16BIT(TA0CCR2); /* Timer0_A3 Capture/Compare 2 *//* Alternate register names */#define TAIV TA0IV /* Timer A Interrupt Vector Word */#define TACTL TA0CTL /* Timer A Control */#define TACCTL0 TA0CCTL0 /* Timer A Capture/Compare Control 0 */#define TACCTL1 TA0CCTL1 /* Timer A Capture/Compare Control 1 */#define TACCTL2 TA0CCTL2 /* Timer A Capture/Compare Control 2 */#define TAR TA0R /* Timer A */#define TACCR0 TA0CCR0 /* Timer A Capture/Compare 0 */#define TACCR1 TA0CCR1 /* Timer A Capture/Compare 1 */#define TACCR2 TA0CCR2 /* Timer A Capture/Compare 2 */#define TAIV_ TA0IV_ /* Timer A Interrupt Vector Word */#define TACTL_ TA0CTL_ /* Timer A Control */#define TACCTL0_ TA0CCTL0_ /* Timer A Capture/Compare Control 0 */#define TACCTL1_ TA0CCTL1_ /* Timer A Capture/Compare Control 1 */#define TACCTL2_ TA0CCTL2_ /* Timer A Capture/Compare Control 2 */#define TAR_ TA0R_ /* Timer A */#define TACCR0_ TA0CCR0_ /* Timer A Capture/Compare 0 */#define TACCR1_ TA0CCR1_ /* Timer A Capture/Compare 1 */#define TACCR2_ TA0CCR2_ /* Timer A Capture/Compare 2 *//* Alternate register names 2 */#define CCTL0 TACCTL0 /* Timer A Capture/Compare Control 0 */#define CCTL1 TACCTL1 /* Timer A Capture/Compare Control 1 */#define CCTL2 TACCTL2 /* Timer A Capture/Compare Control 2 */#define CCR0 TACCR0 /* Timer A Capture/Compare 0 */#define CCR1 TACCR1 /* Timer A Capture/Compare 1 */#define CCR2 TACCR2 /* Timer A Capture/Compare 2 */#define CCTL0_ TACCTL0_ /* Timer A Capture/Compare Control 0 */#define CCTL1_ TACCTL1_ /* Timer A Capture/Compare Control 1 */#define CCTL2_ TACCTL2_ /* Timer A Capture/Compare Control 2 */#define CCR0_ TACCR0_ /* Timer A Capture/Compare 0 */#define CCR1_ TACCR1_ /* Timer A Capture/Compare 1 */#define CCR2_ TACCR2_ /* Timer A Capture/Compare 2 */#define TASSEL1 (0x0200) /* Timer A clock source select 0 */#define TASSEL0 (0x0100) /* Timer A clock source select 1 */#define ID1 (0x0080) /* Timer A clock input divider 1 */#define ID0 (0x0040) /* Timer A clock input divider 0 */#define MC1 (0x0020) /* Timer A mode control 1 */#define MC0 (0x0010) /* Timer A mode control 0 */#define TACLR (0x0004) /* Timer A counter clear */#define TAIE (0x0002) /* Timer A counter interrupt enable */#define TAIFG (0x0001) /* Timer A counter interrupt flag */#define MC_0 (0*0x10u) /* Timer A mode control: 0 - Stop */#define MC_1 (1*0x10u) /* Timer A mode control: 1 - Up to CCR0 */#define MC_2 (2*0x10u) /* Timer A mode control: 2 - Continous up */#define MC_3 (3*0x10u) /* Timer A mode control: 3 - Up/Down */#define ID_0 (0*0x40u) /* Timer A input divider: 0 - /1 */#define ID_1 (1*0x40u) /* Timer A input divider: 1 - /2 */#define ID_2 (2*0x40u) /* Timer A input divider: 2 - /4 */#define ID_3 (3*0x40u) /* Timer A input divider: 3 - /8 */#define TASSEL_0 (0*0x100u) /* Timer A clock source select: 0 - TACLK */#define TASSEL_1 (1*0x100u) /* Timer A clock source select: 1 - ACLK */#define TASSEL_2 (2*0x100u) /* Timer A clock source select: 2 - SMCLK */#define TASSEL_3 (3*0x100u) /* Timer A clock source select: 3 - INCLK */#define CM1 (0x8000) /* Capture mode 1 */#define CM0 (0x4000) /* Capture mode 0 */#define CCIS1 (0x2000) /* Capture input select 1 */#define CCIS0 (0x1000) /* Capture input select 0 */#define SCS (0x0800) /* Capture sychronize */#define SCCI (0x0400) /* Latched capture signal (read) */#define CAP (0x0100) /* Capture mode: 1 /Compare mode : 0 */#define OUTMOD2 (0x0080) /* Output mode 2 */#define OUTMOD1 (0x0040) /* Output mode 1 */#define OUTMOD0 (0x0020) /* Output mode 0 */#define CCIE (0x0010) /* Capture/compare interrupt enable */#define CCI (0x0008) /* Capture input signal (read) */#define OUT (0x0004) /* PWM Output signal if output mode 0 */#define COV (0x0002) /* Capture/compare overflow flag */#define CCIFG (0x0001) /* Capture/compare interrupt flag */#define OUTMOD_0 (0*0x20u) /* PWM output mode: 0 - output only */#define OUTMOD_1 (1*0x20u) /* PWM output mode: 1 - set */#define OUTMOD_2 (2*0x20u) /* PWM output mode: 2 - PWM toggle/reset */#define OUTMOD_3 (3*0x20u) /* PWM output mode: 3 - PWM set/reset */#define OUTMOD_4 (4*0x20u) /* PWM output mode: 4 - toggle */#define OUTMOD_5 (5*0x20u) /* PWM output mode: 5 - Reset */#define OUTMOD_6 (6*0x20u) /* PWM output mode: 6 - PWM toggle/set */#define OUTMOD_7 (7*0x20u) /* PWM output mode: 7 - PWM reset/set */#define CCIS_0 (0*0x1000u) /* Capture input select: 0 - CCIxA */#define CCIS_1 (1*0x1000u) /* Capture input select: 1 - CCIxB */#define CCIS_2 (2*0x1000u) /* Capture input select: 2 - GND */#define CCIS_3 (3*0x1000u) /* Capture input select: 3 - Vcc */#define CM_0 (0*0x4000u) /* Capture mode: 0 - disabled */#define CM_1 (1*0x4000u) /* Capture mode: 1 - pos. edge */#define CM_2 (2*0x4000u) /* Capture mode: 1 - neg. edge */#define CM_3 (3*0x4000u) /* Capture mode: 1 - both edges *//* T0_A3IV Definitions */#define TA0IV_NONE (0x0000) /* No Interrupt pending */#define TA0IV_TACCR1 (0x0002) /* TA0CCR1_CCIFG */#define TA0IV_TACCR2 (0x0004) /* TA0CCR2_CCIFG */#define TA0IV_6 (0x0006) /* Reserved */#define TA0IV_8 (0x0008) /* Reserved */#define TA0IV_TAIFG (0x000A) /* TA0IFG *//************************************************************* Timer1_A5************************************************************/#define __MSP430_HAS_T1A5__ /* Definition to show that Module is available */SFR_16BIT(TA1IV); /* Timer1_A5 Interrupt Vector Word */SFR_16BIT(TA1CTL); /* Timer1_A5 Control */SFR_16BIT(TA1CCTL0); /* Timer1_A5 Capture/Compare Control 0 */SFR_16BIT(TA1CCTL1); /* Timer1_A5 Capture/Compare Control 1 */SFR_16BIT(TA1CCTL2); /* Timer1_A5 Capture/Compare Control 2 */SFR_16BIT(TA1CCTL3); /* Timer1_A5 Capture/Compare Control 3 */SFR_16BIT(TA1CCTL4); /* Timer1_A5 Capture/Compare Control 4 */SFR_16BIT(TA1R); /* Timer1_A5 */SFR_16BIT(TA1CCR0); /* Timer1_A5 Capture/Compare 0 */SFR_16BIT(TA1CCR1); /* Timer1_A5 Capture/Compare 1 */SFR_16BIT(TA1CCR2); /* Timer1_A5 Capture/Compare 2 */SFR_16BIT(TA1CCR3); /* Timer1_A5 Capture/Compare 3 */SFR_16BIT(TA1CCR4); /* Timer1_A5 Capture/Compare 4 *//* Bits are already defined within the Timer0_Ax *//* T1_A5IV Definitions */#define TA1IV_NONE (0x0000) /* No Interrupt pending */#define TA1IV_TACCR1 (0x0002) /* TA1CCR1_CCIFG */#define TA1IV_TACCR2 (0x0004) /* TA1CCR2_CCIFG */#define TA1IV_TACCR3 (0x0006) /* TA1CCR3_CCIFG */#define TA1IV_TACCR4 (0x0008) /* TA1CCR4_CCIFG */#define TA1IV_TAIFG (0x000A) /* TA1IFG *//************************************************************* USCI************************************************************/#define __MSP430_HAS_USCI__ /* Definition to show that Module is available */SFR_8BIT(UCA0CTL0); /* USCI A0 Control Register 0 */SFR_8BIT(UCA0CTL1); /* USCI A0 Control Register 1 */SFR_8BIT(UCA0BR0); /* USCI A0 Baud Rate 0 */SFR_8BIT(UCA0BR1); /* USCI A0 Baud Rate 1 */SFR_8BIT(UCA0MCTL); /* USCI A0 Modulation Control */SFR_8BIT(UCA0STAT); /* USCI A0 Status Register */SFR_8BIT(UCA0RXBUF); /* USCI A0 Receive Buffer */SFR_8BIT(UCA0TXBUF); /* USCI A0 Transmit Buffer */SFR_8BIT(UCA0ABCTL); /* USCI A0 LIN Control */SFR_8BIT(UCA0IRTCTL); /* USCI A0 IrDA Transmit Control */SFR_8BIT(UCA0IRRCTL); /* USCI A0 IrDA Receive Control */SFR_8BIT(UCB0CTL0); /* USCI B0 Control Register 0 */SFR_8BIT(UCB0CTL1); /* USCI B0 Control Register 1 */SFR_8BIT(UCB0BR0); /* USCI B0 Baud Rate 0 */SFR_8BIT(UCB0BR1); /* USCI B0 Baud Rate 1 */SFR_8BIT(UCB0I2CIE); /* USCI B0 I2C Interrupt Enable Register */SFR_8BIT(UCB0STAT); /* USCI B0 Status Register */SFR_8BIT(UCB0RXBUF); /* USCI B0 Receive Buffer */SFR_8BIT(UCB0TXBUF); /* USCI B0 Transmit Buffer */SFR_16BIT(UCB0I2COA); /* USCI B0 I2C Own Address */SFR_16BIT(UCB0I2CSA); /* USCI B0 I2C Slave Address */// UART-Mode Bits#define UCPEN (0x80) /* Async. Mode: Parity enable */#define UCPAR (0x40) /* Async. Mode: Parity 0:odd / 1:even */#define UCMSB (0x20) /* Async. Mode: MSB first 0:LSB / 1:MSB */#define UC7BIT (0x10) /* Async. Mode: Data Bits 0:8-bits / 1:7-bits */#define UCSPB (0x08) /* Async. Mode: Stop Bits 0:one / 1: two */#define UCMODE1 (0x04) /* Async. Mode: USCI Mode 1 */#define UCMODE0 (0x02) /* Async. Mode: USCI Mode 0 */#define UCSYNC (0x01) /* Sync-Mode 0:UART-Mode / 1:SPI-Mode */// SPI-Mode Bits#define UCCKPH (0x80) /* Sync. Mode: Clock Phase */#define UCCKPL (0x40) /* Sync. Mode: Clock Polarity */#define UCMST (0x08) /* Sync. Mode: Master Select */// I2C-Mode Bits#define UCA10 (0x80) /* 10-bit Address Mode */#define UCSLA10 (0x40) /* 10-bit Slave Address Mode */#define UCMM (0x20) /* Multi-Master Environment *///#define res (0x10) /* reserved */#define UCMODE_0 (0x00) /* Sync. Mode: USCI Mode: 0 */#define UCMODE_1 (0x02) /* Sync. Mode: USCI Mode: 1 */#define UCMODE_2 (0x04) /* Sync. Mode: USCI Mode: 2 */#define UCMODE_3 (0x06) /* Sync. Mode: USCI Mode: 3 */// UART-Mode Bits#define UCSSEL1 (0x80) /* USCI 0 Clock Source Select 1 */#define UCSSEL0 (0x40) /* USCI 0 Clock Source Select 0 */#define UCRXEIE (0x20) /* RX Error interrupt enable */#define UCBRKIE (0x10) /* Break interrupt enable */#define UCDORM (0x08) /* Dormant (Sleep) Mode */#define UCTXADDR (0x04) /* Send next Data as Address */#define UCTXBRK (0x02) /* Send next Data as Break */#define UCSWRST (0x01) /* USCI Software Reset */// SPI-Mode Bits//#define res (0x20) /* reserved *///#define res (0x10) /* reserved *///#define res (0x08) /* reserved *///#define res (0x04) /* reserved *///#define res (0x02) /* reserved */// I2C-Mode Bits//#define res (0x20) /* reserved */#define UCTR (0x10) /* Transmit/Receive Select/Flag */#define UCTXNACK (0x08) /* Transmit NACK */#define UCTXSTP (0x04) /* Transmit STOP */#define UCTXSTT (0x02) /* Transmit START */#define UCSSEL_0 (0x00) /* USCI 0 Clock Source: 0 */#define UCSSEL_1 (0x40) /* USCI 0 Clock Source: 1 */#define UCSSEL_2 (0x80) /* USCI 0 Clock Source: 2 */#define UCSSEL_3 (0xC0) /* USCI 0 Clock Source: 3 */#define UCBRF3 (0x80) /* USCI First Stage Modulation Select 3 */#define UCBRF2 (0x40) /* USCI First Stage Modulation Select 2 */#define UCBRF1 (0x20) /* USCI First Stage Modulation Select 1 */#define UCBRF0 (0x10) /* USCI First Stage Modulation Select 0 */#define UCBRS2 (0x08) /* USCI Second Stage Modulation Select 2 */#define UCBRS1 (0x04) /* USCI Second Stage Modulation Select 1 */#define UCBRS0 (0x02) /* USCI Second Stage Modulation Select 0 */#define UCOS16 (0x01) /* USCI 16-times Oversampling enable */#define UCBRF_0 (0x00) /* USCI First Stage Modulation: 0 */#define UCBRF_1 (0x10) /* USCI First Stage Modulation: 1 */#define UCBRF_2 (0x20) /* USCI First Stage Modulation: 2 */#define UCBRF_3 (0x30) /* USCI First Stage Modulation: 3 */#define UCBRF_4 (0x40) /* USCI First Stage Modulation: 4 */#define UCBRF_5 (0x50) /* USCI First Stage Modulation: 5 */#define UCBRF_6 (0x60) /* USCI First Stage Modulation: 6 */#define UCBRF_7 (0x70) /* USCI First Stage Modulation: 7 */#define UCBRF_8 (0x80) /* USCI First Stage Modulation: 8 */#define UCBRF_9 (0x90) /* USCI First Stage Modulation: 9 */#define UCBRF_10 (0xA0) /* USCI First Stage Modulation: A */#define UCBRF_11 (0xB0) /* USCI First Stage Modulation: B */#define UCBRF_12 (0xC0) /* USCI First Stage Modulation: C */#define UCBRF_13 (0xD0) /* USCI First Stage Modulation: D */#define UCBRF_14 (0xE0) /* USCI First Stage Modulation: E */#define UCBRF_15 (0xF0) /* USCI First Stage Modulation: F */#define UCBRS_0 (0x00) /* USCI Second Stage Modulation: 0 */#define UCBRS_1 (0x02) /* USCI Second Stage Modulation: 1 */#define UCBRS_2 (0x04) /* USCI Second Stage Modulation: 2 */#define UCBRS_3 (0x06) /* USCI Second Stage Modulation: 3 */#define UCBRS_4 (0x08) /* USCI Second Stage Modulation: 4 */#define UCBRS_5 (0x0A) /* USCI Second Stage Modulation: 5 */#define UCBRS_6 (0x0C) /* USCI Second Stage Modulation: 6 */#define UCBRS_7 (0x0E) /* USCI Second Stage Modulation: 7 */#define UCLISTEN (0x80) /* USCI Listen mode */#define UCFE (0x40) /* USCI Frame Error Flag */#define UCOE (0x20) /* USCI Overrun Error Flag */#define UCPE (0x10) /* USCI Parity Error Flag */#define UCBRK (0x08) /* USCI Break received */#define UCRXERR (0x04) /* USCI RX Error Flag */#define UCADDR (0x02) /* USCI Address received Flag */#define UCBUSY (0x01) /* USCI Busy Flag */#define UCIDLE (0x02) /* USCI Idle line detected Flag *///#define res (0x80) /* reserved *///#define res (0x40) /* reserved *///#define res (0x20) /* reserved *///#define res (0x10) /* reserved */#define UCNACKIE (0x08) /* NACK Condition interrupt enable */#define UCSTPIE (0x04) /* STOP Condition interrupt enable */#define UCSTTIE (0x02) /* START Condition interrupt enable */#define UCALIE (0x01) /* Arbitration Lost interrupt enable */#define UCSCLLOW (0x40) /* SCL low */#define UCGC (0x20) /* General Call address received Flag */#define UCBBUSY (0x10) /* Bus Busy Flag */#define UCNACKIFG (0x08) /* NAK Condition interrupt Flag */#define UCSTPIFG (0x04) /* STOP Condition interrupt Flag */#define UCSTTIFG (0x02) /* START Condition interrupt Flag */#define UCALIFG (0x01) /* Arbitration Lost interrupt Flag */#define UCIRTXPL5 (0x80) /* IRDA Transmit Pulse Length 5 */#define UCIRTXPL4 (0x40) /* IRDA Transmit Pulse Length 4 */#define UCIRTXPL3 (0x20) /* IRDA Transmit Pulse Length 3 */#define UCIRTXPL2 (0x10) /* IRDA Transmit Pulse Length 2 */#define UCIRTXPL1 (0x08) /* IRDA Transmit Pulse Length 1 */#define UCIRTXPL0 (0x04) /* IRDA Transmit Pulse Length 0 */#define UCIRTXCLK (0x02) /* IRDA Transmit Pulse Clock Select */#define UCIREN (0x01) /* IRDA Encoder/Decoder enable */#define UCIRRXFL5 (0x80) /* IRDA Receive Filter Length 5 */#define UCIRRXFL4 (0x40) /* IRDA Receive Filter Length 4 */#define UCIRRXFL3 (0x20) /* IRDA Receive Filter Length 3 */#define UCIRRXFL2 (0x10) /* IRDA Receive Filter Length 2 */#define UCIRRXFL1 (0x08) /* IRDA Receive Filter Length 1 */#define UCIRRXFL0 (0x04) /* IRDA Receive Filter Length 0 */#define UCIRRXPL (0x02) /* IRDA Receive Input Polarity */#define UCIRRXFE (0x01) /* IRDA Receive Filter enable *///#define res (0x80) /* reserved *///#define res (0x40) /* reserved */#define UCDELIM1 (0x20) /* Break Sync Delimiter 1 */#define UCDELIM0 (0x10) /* Break Sync Delimiter 0 */#define UCSTOE (0x08) /* Sync-Field Timeout error */#define UCBTOE (0x04) /* Break Timeout error *///#define res (0x02) /* reserved */#define UCABDEN (0x01) /* Auto Baud Rate detect enable */#define UCGCEN (0x8000) /* I2C General Call enable */#define UCOA9 (0x0200) /* I2C Own Address 9 */#define UCOA8 (0x0100) /* I2C Own Address 8 */#define UCOA7 (0x0080) /* I2C Own Address 7 */#define UCOA6 (0x0040) /* I2C Own Address 6 */#define UCOA5 (0x0020) /* I2C Own Address 5 */#define UCOA4 (0x0010) /* I2C Own Address 4 */#define UCOA3 (0x0008) /* I2C Own Address 3 */#define UCOA2 (0x0004) /* I2C Own Address 2 */#define UCOA1 (0x0002) /* I2C Own Address 1 */#define UCOA0 (0x0001) /* I2C Own Address 0 */#define UCSA9 (0x0200) /* I2C Slave Address 9 */#define UCSA8 (0x0100) /* I2C Slave Address 8 */#define UCSA7 (0x0080) /* I2C Slave Address 7 */#define UCSA6 (0x0040) /* I2C Slave Address 6 */#define UCSA5 (0x0020) /* I2C Slave Address 5 */#define UCSA4 (0x0010) /* I2C Slave Address 4 */#define UCSA3 (0x0008) /* I2C Slave Address 3 */#define UCSA2 (0x0004) /* I2C Slave Address 2 */#define UCSA1 (0x0002) /* I2C Slave Address 1 */#define UCSA0 (0x0001) /* I2C Slave Address 0 *//************************************************************* WATCHDOG TIMER************************************************************/#define __MSP430_HAS_WDT__ /* Definition to show that Module is available */SFR_16BIT(WDTCTL); /* Watchdog Timer Control *//* The bit names have been prefixed with "WDT" */#define WDTIS0 (0x0001)#define WDTIS1 (0x0002)#define WDTSSEL (0x0004)#define WDTCNTCL (0x0008)#define WDTTMSEL (0x0010)#define WDTNMI (0x0020)#define WDTNMIES (0x0040)#define WDTHOLD (0x0080)#define WDTPW (0x5A00)/* WDT-interval times [1ms] coded with Bits 0-2 *//* WDT is clocked by fSMCLK (assumed 1MHz) */#define WDT_MDLY_32 (WDTPW+WDTTMSEL+WDTCNTCL) /* 32ms interval (default) */#define WDT_MDLY_8 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS0) /* 8ms " */#define WDT_MDLY_0_5 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1) /* 0.5ms " */#define WDT_MDLY_0_064 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1+WDTIS0) /* 0.064ms " *//* WDT is clocked by fACLK (assumed 32KHz) */#define WDT_ADLY_1000 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL) /* 1000ms " */#define WDT_ADLY_250 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS0) /* 250ms " */#define WDT_ADLY_16 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1) /* 16ms " */#define WDT_ADLY_1_9 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0) /* 1.9ms " *//* Watchdog mode -> reset after expired time *//* WDT is clocked by fSMCLK (assumed 1MHz) */#define WDT_MRST_32 (WDTPW+WDTCNTCL) /* 32ms interval (default) */#define WDT_MRST_8 (WDTPW+WDTCNTCL+WDTIS0) /* 8ms " */#define WDT_MRST_0_5 (WDTPW+WDTCNTCL+WDTIS1) /* 0.5ms " */#define WDT_MRST_0_064 (WDTPW+WDTCNTCL+WDTIS1+WDTIS0) /* 0.064ms " *//* WDT is clocked by fACLK (assumed 32KHz) */#define WDT_ARST_1000 (WDTPW+WDTCNTCL+WDTSSEL) /* 1000ms " */#define WDT_ARST_250 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS0) /* 250ms " */#define WDT_ARST_16 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1) /* 16ms " */#define WDT_ARST_1_9 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0) /* 1.9ms " *//* INTERRUPT CONTROL *//* These two bits are defined in the Special Function Registers *//* #define WDTIE 0x01 *//* #define WDTIFG 0x01 *//************************************************************* Interrupt Vectors (offset from 0xFFE0)************************************************************/#define VECTOR_NAME(name) name##_ptr#define EMIT_PRAGMA(x) _Pragma(#x)#define CREATE_VECTOR(name) void (* const VECTOR_NAME(name))(void) = &name#define PLACE_VECTOR(vector,section) EMIT_PRAGMA(DATA_SECTION(vector,section))#define ISR_VECTOR(func,offset) CREATE_VECTOR(func); \PLACE_VECTOR(VECTOR_NAME(func), offset)#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define BASICTIMER_VECTOR ".int00" /* 0xFFE0 Basic Timer */#else#define BASICTIMER_VECTOR (0 * 1u) /* 0xFFE0 Basic Timer *//*#define BASICTIMER_ISR(func) ISR_VECTOR(func, ".int00") */ /* 0xFFE0 Basic Timer */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define PORT2_VECTOR ".int01" /* 0xFFE2 Port 2 */#else#define PORT2_VECTOR (1 * 1u) /* 0xFFE2 Port 2 *//*#define PORT2_ISR(func) ISR_VECTOR(func, ".int01") */ /* 0xFFE2 Port 2 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define PORT1_VECTOR ".int04" /* 0xFFE8 Port 1 */#else#define PORT1_VECTOR (4 * 1u) /* 0xFFE8 Port 1 *//*#define PORT1_ISR(func) ISR_VECTOR(func, ".int04") */ /* 0xFFE8 Port 1 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define TIMER0_A1_VECTOR ".int05" /* 0xFFEA Timer0_A CC1-2, TA0 */#else#define TIMER0_A1_VECTOR (5 * 1u) /* 0xFFEA Timer0_A CC1-2, TA0 *//*#define TIMER0_A1_ISR(func) ISR_VECTOR(func, ".int05") */ /* 0xFFEA Timer0_A CC1-2, TA0 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define TIMER0_A0_VECTOR ".int06" /* 0xFFEC Timer0_A CC0 */#else#define TIMER0_A0_VECTOR (6 * 1u) /* 0xFFEC Timer0_A CC0 *//*#define TIMER0_A0_ISR(func) ISR_VECTOR(func, ".int06") */ /* 0xFFEC Timer0_A CC0 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define ADC10_VECTOR ".int07" /* 0xFFEE ADC10 */#else#define ADC10_VECTOR (7 * 1u) /* 0xFFEE ADC10 *//*#define ADC10_ISR(func) ISR_VECTOR(func, ".int07") */ /* 0xFFEE ADC10 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define USCIAB0TX_VECTOR ".int08" /* 0xFFF0 USCI A0/B0 Transmit */#else#define USCIAB0TX_VECTOR (8 * 1u) /* 0xFFF0 USCI A0/B0 Transmit *//*#define USCIAB0TX_ISR(func) ISR_VECTOR(func, ".int08") */ /* 0xFFF0 USCI A0/B0 Transmit */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define USCIAB0RX_VECTOR ".int09" /* 0xFFF2 USCI A0/B0 Receive */#else#define USCIAB0RX_VECTOR (9 * 1u) /* 0xFFF2 USCI A0/B0 Receive *//*#define USCIAB0RX_ISR(func) ISR_VECTOR(func, ".int09") */ /* 0xFFF2 USCI A0/B0 Receive */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define WDT_VECTOR ".int10" /* 0xFFF4 Watchdog Timer */#else#define WDT_VECTOR (10 * 1u) /* 0xFFF4 Watchdog Timer *//*#define WDT_ISR(func) ISR_VECTOR(func, ".int10") */ /* 0xFFF4 Watchdog Timer */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define COMPARATORA_VECTOR ".int11" /* 0xFFF6 Comparator A */#else#define COMPARATORA_VECTOR (11 * 1u) /* 0xFFF6 Comparator A *//*#define COMPARATORA_ISR(func) ISR_VECTOR(func, ".int11") */ /* 0xFFF6 Comparator A */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define TIMER1_A1_VECTOR ".int12" /* 0xFFF8 Timer1_A CC1-4, TA1 */#else#define TIMER1_A1_VECTOR (12 * 1u) /* 0xFFF8 Timer1_A CC1-4, TA1 *//*#define TIMER1_A1_ISR(func) ISR_VECTOR(func, ".int12") */ /* 0xFFF8 Timer1_A CC1-4, TA1 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define TIMER1_A0_VECTOR ".int13" /* 0xFFFA Timer1_A CC0 */#else#define TIMER1_A0_VECTOR (13 * 1u) /* 0xFFFA Timer1_A CC0 *//*#define TIMER1_A0_ISR(func) ISR_VECTOR(func, ".int13") */ /* 0xFFFA Timer1_A CC0 */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define NMI_VECTOR ".int14" /* 0xFFFC Non-maskable */#else#define NMI_VECTOR (14 * 1u) /* 0xFFFC Non-maskable *//*#define NMI_ISR(func) ISR_VECTOR(func, ".int14") */ /* 0xFFFC Non-maskable */ /* CCE V2 Style */#endif#ifdef __ASM_HEADER__ /* Begin #defines for assembler */#define RESET_VECTOR ".reset" /* 0xFFFE Reset [Highest Priority] */#else#define RESET_VECTOR (15 * 1u) /* 0xFFFE Reset [Highest Priority] *//*#define RESET_ISR(func) ISR_VECTOR(func, ".int15") */ /* 0xFFFE Reset [Highest Priority] */ /* CCE V2 Style */#endif/* Alternate Names *//************************************************************* End of Modules************************************************************/#ifdef __cplusplus}#endif /* extern "C" */#endif /* #ifndef __msp430x41x2 */